Products

Blacklisted RC 2023 SORCCA Legal Puzzle Piece R...

Blacklisted RC Puzzle Piece Roof Rack w/Mounting Hardware

Blacklisted RC Puzzle Piece Roof Rack w/Mounting Hardware

Blacklisted RC 2023 SORCCA Legal Spade Roof Rac...

Blacklisted RC 2023 SORCCA Legal Spade Roof Rack w/Mounting Hardware

Blacklisted RC 2023 SORCCA Legal Spade Roof Rack w/Mounting Hardware

Blacklisted RC 2023 SORCCA Legal Ultralight Roo...

Blacklisted RC Ultralight Roof Rack w/Mounting Hardware

Blacklisted RC Ultralight Roof Rack w/Mounting Hardware

Blacklisted RC Lightweight Aluminum Seats

Lightweight aluminum bucket seats. Weighing in at 28.5 grams a pair, they will add some style to ...

Lightweight aluminum bucket seats. Weighing in at 28.5 grams a pair, they will add some style to your interior without killing your center of gravity. Includes 2 seats. 

BLUE JEKYLL AND HYDE REVAMP

JEKYLL AND HYDE REVAMP!! HERE IT IS! THE RE RELEASE OF THE OG JEKYLL AND HYDE!! DESIGNED FOR THE ...

JEKYLL AND HYDE REVAMP!! HERE IT IS! THE RE RELEASE OF THE OG JEKYLL AND HYDE!! DESIGNED FOR THE ULTIMATE FORWARD SKID SETUP! A FULL FORWARD TRANS AND TCASE SETUP. THIS IS THE VERY SETUP USED IN OUR TOP PERFORMING NINJA AND KATANA CHASSIS. 26% UNDERDRIVE TO THE REAR. EXTREMELY FORWARD SKID SETUP WITH STILL OUR 12 DEGREE BREAKOVER! WE WERE THE FIRST TO DO 12 DEGREES AND CONTINUE TO BE THE STANDARD EVERYONE ELSE SETS THEIR BUILDS TO! MASSIVE AMOUNTS OF BREAKOVER CLEARANCE, BEHIND THE SKID AT TH...

Bob Smith Industries Extra Fine Extender Tips F...

This is a box of thirty six Bob Smith Industries Extra Fine CA Bottle Extender Tips. These work b...

This is a box of thirty six Bob Smith Industries Extra Fine CA Bottle Extender Tips. These work best with BSI products.

Bob Smith Industries IC-2000 Black Rubber Tough...

Ic-2000 Black Rubber-Toughened CA Glue 1oz

Ic-2000 Black Rubber-Toughened CA Glue 1oz

Bob Smith Industries INSTA-CURE POCKET Super Th...

This is a 3/4 ounce bottle of Bob Smith Industries Super Thin INSTA-CURE™ Pocket CA Glue with a P...

This is a 3/4 ounce bottle of Bob Smith Industries Super Thin INSTA-CURE™ Pocket CA Glue with a Pin in Cap Lid. INSTA-CURE™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa s...

Bob Smith Industries INSTA-CURE+ Gap Filling CA...

This is a two ounce bottle of Bob Smith Industries INSTA-CURE+™ Gap Filling CA Glue. INSTA-CURE+™...

This is a two ounce bottle of Bob Smith Industries INSTA-CURE+™ Gap Filling CA Glue. INSTA-CURE+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin ...

Bob Smith Industries INSTA-FLEX Flexible Thin C...

This is a one ounce bottle of Bob Smith Industries INSTA-FLEX™ Flexible Thin CA Glue. INSTA-FLEX™...

This is a one ounce bottle of Bob Smith Industries INSTA-FLEX™ Flexible Thin CA Glue. INSTA-FLEX™ flexible thin CA is ideal for many applications, including the installation of CA hinges. When cured, INSTA-FLEX™ does not turn brittle and remains clear, even if accelerated with INSTA-SET™. It has superior shock resistance. Although not as thin in consistency as INSTA-CURE™, INSTA-FLEX™ still has good penetrating qualities and its application can be easier to control. For CA hinges, we recommen...

Bob Smith Industries INSTA-FLEX+ Clear Rubber T...

This is a one ounce bottle of Bob Smith Industries INSTA-FLEX+™ Clear Rubber Toughened CA Glue. I...

This is a one ounce bottle of Bob Smith Industries INSTA-FLEX+™ Clear Rubber Toughened CA Glue. INSTA-FLEX+™ clear rubber toughened has similar qualities to our black IC-2000™ but can be used in applications where you do not want the adhesive to be seen. The carbon component of IC-2000™ that gives the CA its black color also contributes to its unsurpassed strength. Since INSTA-FLEX+™ has this carbon removed, its strength is a little less than IC-2000™ but still superior to standard CA's. When...

Bob Smith Industries INSTA-SET Foam Safe Accele...

This is a two fluid ounce Pump Spray bottle of Bob Smith Industries INSTA-SET™ Foam Safe CA Accel...

This is a two fluid ounce Pump Spray bottle of Bob Smith Industries INSTA-SET™ Foam Safe CA Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a ...

Bob Smith Industries MAXI-CURE POCKET Extra Thi...

This is a 3/4 ounce bottle of Bob Smith Industries MAXI-CURE Extra Thick Pocket CA Glue with a Pi...

This is a 3/4 ounce bottle of Bob Smith Industries MAXI-CURE Extra Thick Pocket CA Glue with a Pin in Cap Lid. MAXI-CURE™ extra thick CA is the best CA for most plastics, including GE’s Lexan. MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic.MAXI-CURE™ bonds fiberglass, hardwood,...

Bob Smith Industries Pocket CA Extender Tips (5)

This is a bag of five Bob Smith Industries Pocket CA Bottle Extender Tips. These work best with B...

This is a bag of five Bob Smith Industries Pocket CA Bottle Extender Tips. These work best with BSI products.

Bob Smith Industries SUPER-GOLD Thin Odorless F...

This is a half ounce bottle of Bob Smith Industries SUPER-GOLD™ Odorless, Foam Safe CA Glue. SUPE...

This is a half ounce bottle of Bob Smith Industries SUPER-GOLD™ Odorless, Foam Safe CA Glue. SUPER-GOLD™ and SUPER-GOLD+™ are BSI's odorless INSTA-CURE CAs. They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for ...

Bob Smith Industries ULTRA-CURE Medium CA Tire ...

This is a one ounce bottle of Bob Smith Industries ULTRA-CURE Medium CA Tire Glue. ULTRA-CURE Tir...

This is a one ounce bottle of Bob Smith Industries ULTRA-CURE Medium CA Tire Glue. ULTRA-CURE Tire Glue has been rated by many racers as the best CA for use on tires, and has a claimed to dry in 5-10 seconds. Ultra-Cure has a thickness in-between BSI’s Insta-Cure and Insta-Cure+ blends, with a viscosity of 80 cps. Package includes one bottle of ULTRA-CURE Medium-Thin CA glue.

Bombproof Warranty Repair or Maintenance

***DO NOT BUY THIS*** ...unless* *Please proceed to checkout with this and only this in your cart...

***DO NOT BUY THIS*** ...unless* *Please proceed to checkout with this and only this in your cart, if directed by management because you sent a Bombproof in for Warranty Repair or Maintenance. This allows us to have your shipping address and print the label through our system for tracking. FREE - If your transmission is Damaged for any reason, your return shipping is covered under your Warranty. Please choose the Free shipping at the time of checkout. Unless you want a faster return postal s...

BowHouse RC SCX6 SVT Carbon Fiber Slipper Pads

Bowhouse SCX6 SVT Carbon Fiber Slipper Pads are a durable upgrade for the stock SCX6 slipper pads...

Bowhouse SCX6 SVT Carbon Fiber Slipper Pads are a durable upgrade for the stock SCX6 slipper pads that won't break down from heat or grease. Belleville washers are included to maintain consistent pressure on the slipper plates and pads. The result is a durable slipper system that allows you to adjust and maintain tension to optimize performance and protect the  running gear. Installation: Remove transmission and save all mounting hardware. Remove motor and spur cover and save all mounting ...

BowHouse RC Traxxas TRX-4 N2R High Clearance Skid

Package includes: 1x skid Installation notes Reuse stock hardware in stock locations EXCEPT a...

Package includes: 1x skid Installation notes Reuse stock hardware in stock locations EXCEPT as follows: (a) use M3x8 FHCS under front of skid to attach transmission (replaces stock M3x10 BHCS) (b) use M3x16 BHCS to attach front lower links (replaces stock M3x15 BHCS) (c) use M3x8 BHCS to attach right rear of transmission (replaces stock M3x10 BHCS) (d) use M3x30 BHCS to attach rear upper links (replaces stock M3x25 BHCS) Completely remove side tray on right side before installing N2R sk...

BowHouse RC TRX-4 Molded Low CG Battery Tray

The BowHouse RC TRX-4 Molded Low CG Battery Tray is an injection molded option that allows you to...

The BowHouse RC TRX-4 Molded Low CG Battery Tray is an injection molded option that allows you to take advantage of lower battery placement by holding the battery lower in the frame for the ultimate in low CG performance. The tray was designed using 3D imaging technology to take full advantage of nearly every available cubic millimeter to lower the battery tray floor, lowering the center of gravity and making more room for more battery options! The tray is molded from a durable nylon compound...

Brass Front Steering Knuckle: SCX24

Features: CNC machined solid brass Heavy to add weight to vehicle for greater stability and ...

Features: CNC machined solid brass Heavy to add weight to vehicle for greater stability and lower CG Cutouts on knuckle for access to outer bearing race for easy bearing removal Direct replacement for factory plastic steering knuckles Includes: (2) Brass steering knuckles

Brushed Motor for Axial SCX24

NJORA Brushed Motor 66T 50T for 1:24 RC Crawler Axial SCX24 AXI90081 AXI00002 AXI00001 AXI00004 U...

NJORA Brushed Motor 66T 50T for 1:24 RC Crawler Axial SCX24 AXI90081 AXI00002 AXI00001 AXI00004 Upgrade PartsNotes: 050 motors require a different mounting plate with 2 extra holes. 050 motors are longer than stock motor, so one of the battery tray posts needs to be cut off to fit. Suit for: Upgrade motor parts for Axial SCX24Features: High Torque Magnet and Rotor Tuned for Rock Climbing 050 66T Motor II Specifications: Size: longer than stock motor Turn: 66T Weight: 19g Rated Voltage: 7...

Budget Steel Driveshafts - *Order By Measurement*

Budget Friendly Steel Driveshafts Order By Measurement PRODUCT DESCRIPTION: These are the B...

Budget Friendly Steel Driveshafts Order By Measurement PRODUCT DESCRIPTION: These are the Budget Friendly Steel Driveshafts 30° of articulation 5mm Output size M4 Set screws (uses a 2mm Driver)  NO WARRANTY ON THESE SHAFTS (Sorry, If you need a warranty, checkout our S4 Driveshafts) This listing INCLUDES 1 full driveshaft. For most trucks you will need 2.   ORDERING NOTES: Lengths are measured from MOUNTING PIN HOLE to MOUNTING PIN HOLE TRAVEL LENGTHS LISTED ARE FULLY COMPRESSED TO F...

Button Head Screws, Steel, Black Oxide, M4 x 14...

This is a pack of ten replacement Losi 4x14mm Button Head Hex Screws. 

This is a pack of ten replacement Losi 4x14mm Button Head Hex Screws. 

Carryall RC CARC BackpaX with Orange Accents

The CARC Bag is designed from ground up and built to CARC specs.  You won’t find another pack li...

The CARC Bag is designed from ground up and built to CARC specs.  You won’t find another pack like it.  This unique and designed for RC companion is exactly what you need for your adventures.  The bag is built so well it works perfectly for any 3-day trip or even a bug out bag!  The materials are event weather resistant to ensure your equipment stays safe. Dimensions: • 45L 3-day Bag • Easily fits a 17” laptop • Bladder bag/Camel pack ready with Velcro Hanger  • Dual belt system fo...

CASTLE CREATIONS 1/10 COPPERHEAD, 16.8V, Sensor...

Key Features Waterproof design, potted in durable injection molded case Data Logging Fully prog...

Key Features Waterproof design, potted in durable injection molded case Data Logging Fully programmable CRYO-DRIVE™ technology SMARTSENSE™ Dual use fan guard

Castle Creations 10 Amp Adjustable BEC

This is the Castle Creations CCBEC, 10 Amp Adjustable BEC. The CC BEC is a little device that eli...

This is the Castle Creations CCBEC, 10 Amp Adjustable BEC. The CC BEC is a little device that eliminates the need for a receiver and servo battery pack. It draws higher voltage from the motor batteries and drops it to a voltage level that is suitable for your receiver and servos. This is required in applications which draw high power for multiple servos or use more than 3S motor packs, as most ESCs with linear BECs are not designed for these applications.Specifications:Current Output: Peak: 1...

CASTLE CREATIONS B-LINK Bluetooth Adapter

Features: WIRELESS BLUETOOTH COMMUNICATION allows you to interface with most Castle Link compat...

Features: WIRELESS BLUETOOTH COMMUNICATION allows you to interface with most Castle Link compatible ESCs and accessories to change parameters and update  firmware. COMPACT AND LIGHTWEIGHT at 1.20" x .81" x .25" (30.48mm x 20.55mm x 6.55mm) and 0.23oz (6.62g), it can be installed in the vehicle or airframe without significantly increasing model weight. CONVENIENT WATERPROOF DESIGN allows you to quickly adjust settings in the field without disconnecting or disassembling the model. It can st...

Castle Creations Cobra 8 6S 1/8 Scale Brushless...

The Castle Creations Cobra 8 ESC has been designed dominating force supported by cutting-edge tec...

The Castle Creations Cobra 8 ESC has been designed dominating force supported by cutting-edge technology. With a 32-bit dual-core processor and featuring Cryo-Drive technology, this ESC is an excellent choice for 1/8 scale buggies, truggies, on-road vehicles, as well as 1/10 monster trucks weighing up to 15lbs. Boasting a waterproof design and an aluminum case, this ESC is ready for all weather performance. About The Cobra 8 Combo: 32-Bit Processor Using the state-of-the-art 32-bit processor...

CASTLE CREATIONS Copperhead 10 1410-3800Kv Moto...

In The Box (1) Copperhead 10 Special Edition ESC (1) 1410-3800Kv Motor (1) Direct connect senso...

In The Box (1) Copperhead 10 Special Edition ESC (1) 1410-3800Kv Motor (1) Direct connect sensor wire (1) Sensor port dust cover (1) Decals (1) Audible alert reference (1) Coupon for free Castle Link (1) Quick start guide

CASTLE CREATIONS Copperhead 10 16.8V Waterproof...

Overview Copperhead 10 is ideal for those who desire high efficiency, sensored motor support and ...

Overview Copperhead 10 is ideal for those who desire high efficiency, sensored motor support and advanced features for their 10th scale stock upgrade or build. Striking in appearance, the Horizon Hobby Special Edition Copperhead 10 includes CRYO-DRIVE technology, data logging and a selectable BEC with Castle's signature reliability and performance. The Copperhead 10 is more than just a pretty face, with a robust hardware design and flexible tuning options to dominate any terrain and enhance a...

CASTLE CREATIONS COPPERHEAD 10 Brushless ESC / ...

COPPERHEAD 10 Features Input Voltage Range for 1412-3200Kv 5mm Combo : 2s-4s LiPo SMARTSENSE...

COPPERHEAD 10 Features Input Voltage Range for 1412-3200Kv 5mm Combo : 2s-4s LiPo SMARTSENSE™, SENSORED ONLY and BRUSHED Running Modes Selectable 5.5V or 7.5V (6A peak) internal BEC (Battery Eliminator Circuit) CRYO-DRIVE™ Technology minimizes the amount of time the ESC’s electrical components spend generating heat, resulting in improved thermal performance during partial throttle operation where the majority of driving occurs. ESC is housed in a durable injection molded case and potted ...

CASTLE CREATIONS LINK V3 USB PROGRAMMING KIT

Program your Castle brushless ESCs and accessories on your Windows® PC with the Castle Link USB...

Program your Castle brushless ESCs and accessories on your Windows® PC with the Castle Link USB programming kit. Set up of programmable options with point and click ease View your current program settings Air users can customize values for low-voltage cutoff, prop brake strength, governor gain and more Surface users can customize values for low-voltage cutoff, drag brake, torque limiting and more Download new software updates as they become available Simple programming interface featuring...